model LEP100F-24 lep100f-36 lep100f-48 dc output +24v 4.2 ( peak 7 ) a +36v 2.8 ( peak 4.7 ) a +48v 2.1 ( peak 3.5 ) a specifications model LEP100F-24 lep100f-36 lep100f-48 input voltage[v] ac85 - 264 1 f or dc 120 - 370 current[a] acin 100v 1.4typ ( io=100% ) acin 200v 0.7typ ( io=100% ) frequency[hz] 50/60 ( 47-63 ) or dc efficiency[%] acin 100v 81typ ( io=100% ) 82typ ( io=100% ) 83typ ( io=100% ) acin 200v 84typ ( io=100% ) 85typ ( io=100% ) 85typ ( io=100% ) power factor acin 100v 0.98typ ( io=100% ) acin 200v 0.93typ ( io=100% ) inrush current[a] acin 100v 15typ ( io=100% )( at cold start )( ta=25 c ) acin 200v 30typ ( io=100% )( at cold start )( ta=25 c ) leakage current[ma] 0.75max ( 60hz , according to iec60950 and den-an ) output voltage[v] +24 +36 +48 current[a] * 2 0 - 4.2 ( peak 7 ) 0 - 2.8 ( peak 4.7 ) 0 - 2.1 ( peak 3.5 ) wattage[w] 100.8 ( peak 168 ) 100.8 ( peak 169.2 ) 100.8 ( peak 168 ) line regulation[mv] 48max 48max 48max load regulation[mv] 76max 90max 150max ripple[mvp-p] 0to+50 c * 3 120max 120max 150max -10-0 c * 3 160max 160max 300max ripple noise[mvp-p] 0to+50 c * 3 150max 150max 250max -10-0 c * 3 180max 180max 350max temperature regulation[mv] 0to+50 c 120max 150max 240max -10 to +50 c 145max 180max 300max drift[mv] * 4 48max 48max 48max start-up time[ms] 500max ( acin 100v , io=100% ) hold-up time[ms] 20typ ( acin 100v , io=100% ) output voltage adjustment range[v] 21.4 - 26.4 26.4 - 39.6 39.6 - 52.8 output voltage setting[v] 23.0 - 25.0 35.0 - 37.0 46.0 - 50.0 protection circuit and others overcurrent protection works over 101% of peak current and recovers automatically overvoltage protection works at 115 - 140% of rating remote on/off option ( refer to instruction manual ) isolation input-output - rc * 5 ac3 , 000v 1minute , cutoff current = 10ma , dc500v 50m w min ( at room temperature ) input-fg ac2 , 000v 1minute , cutoff current = 10ma , dc500v 50m w min ( at room temperature ) output - rc-fg * 5 ac500v 1minute , cutoff current = 100ma , dc500v 50m w min ( at room temperature ) output-rc * 5 ac100v 1minute , cutoff current = 100ma , dc100v 10m w min ( at room temperature ) environment operating temp. , humid.and altitude -10 to +70 c , 20 - 90%rh ( non condensing )( refer to derating curve ), 3 , 000m ( 10 , 000feet ) max storage temp. , humid.and altitude -20 to +75 c , 20 - 90%rh ( non condensing ), 9 , 000m ( 30 , 000feet ) max vibration 10 - 55hz , 19.6m/s 2 ( 2g ), 3minutes period , 60minutes each along x , y and z axis impact 196.1m/s 2 ( 20g ), 11ms , once each x , y and z axis safety and noise regulations agency approvals ul60950-1 , c-ul ( csa60950-1 ), en60950-1 , en60065 , en50178 complies with den-an and iec60950-1 ( at only ac input ) conducted noise complies with fcc-b , cispr22-b , en55022-b , vcci-b harmonic attenuator complies with iec61000-3-2 others case size/weight 75 x 35 x 222mm [2.95 x 1.38 x 8.74 inches] ( w x h x d ) /380g max ( without chassis and cover ) cooling method convection * 7 * 1 specification is changed at option, refer to instruction manual 6. * 2 peak loading for 10sec. and duty 35% max, refer to instruction manual 5. in detail. * 3 this is the value that measured on measuring board with capacitor of 22 m f within 150mm from output terminal.measured by 20mhz oscilloscope or ripple-noise meter (equivalent to keisoku-giken: rm101). * 4 drift is the change in dc output for an eight hour period after a half-hour warm-up at 25 c , with the input voltage held constant at the rated input/output. * 5 applicable when remote control (optional) is added. * 6 please contact us about safety approvals for the model with option. * 7 please contact us about class c. * parallel operation with other model is not possible. * derating is required when operated with chassis and cover. * a sound may occur from power supply at peak loading. lep100f ac-dc power supplies open frame/ enclosed type lep 100 f -24 - o ordering information 1 series name 2 output wattage 3 universal input 4 output voltage 5 optional * 1 * 6 g :low leakage current r :with remote on/off s :with chassis sn:with chassis & cover t :vertical terminal block u :operating stop voltage is set at a lower value z :with zt r 12345 lep lep-2 recommended emi/emc filter nac-06-472 high voltage pulse noise type : nap series low leakage current type : nam series * the emi/emc filter is recommended * to connect with several devices.
? input harmonic current ( LEP100F-24 ) ? efficiency ( LEP100F-24 ) ? input harmonic current ( LEP100F-24 ) ? rise time & fall time ( LEP100F-24 ) dc output ac input io=100% 20ms/div 100ms/div acin 100v 86 78 80 82 84 76 100 60 140 180 220 260 300 100% 50% load factor load factor efficiency input voltage v 010203040 0.01 0.001 0.1 1 10 load factor input voltage ac harmonic current standard class a (at odd number) 100% 100v harmonic order harmonic current a 010203040 0.01 0.001 0.1 1 10 load factor input voltage ac harmonic current standard class a (at odd number) 100% 230v harmonic order harmonic current a lep lep-3 lep100f external view i / o connector mating connector terminal (mfr: j.s.t.) cn1 cn2 cn3 cn4 b3p5-vh b8p-vh b2b-xh-a b3b-xh-a vhr-5n vhr-8n xhp-2 xhp-3 chain : svh-21t-p1.1 loose: bvh-21t-p1.1 chain : svh-21t-p1.1 loose: bvh-21t-p1.1 chain : sxh-001t-p0.6 loose: bxh-001t-p0.6 chain : sxh-001t-p0.6 loose: bxh-001t-p0.6 ? keep drawing current per pin below 5a(7a at peak load)for cn2 ? weight: 380g max ? tolerance: t 1 [ t 0.04] ? dimensions in mm, [ ]=inches ? pcb material : cem3 ? chassis and cover is optional. ? mounting torque: 1.5n m(16kgf cm)max pin connection pin no. 1 2 3 4 5 input ac(l) ac(n) fg cn1 pin no. output cn2 (option) pin no. remote on/off cn3 rc( + ) rc( - ) 1 , , 23 , 4 , 67 , 8 5 , 1 2 (option) pin no. -z cn4 + com - 1 2 3 - v + v (without chassis and cover) (option) (option) 4.5 235 + - 0.5 25 + - 0.5 45 + - 0.5 8 2- o 4.5 cn3 cn4 o 4.5 2-m4 mounting hole mounting hole 4-m4 8 235 + - 0.5 252 rc( - ) rc( + ) + com - name plate connector for remote on/off (option) voltage adjust mounting hole 3- o 3.5 + - 0.5 + - 0.5 pcb t=1.6 cn4 cn3 (lead) 3 max connector for -z (option) cn2 mounting hole o 3.5 - 4.0 [0.14 - 0.16] cn1 input(l) input(n) fg c119 (68) cn2 4.5 42 85 46 15 20 cn1 30 20 cn3 cn4 (176) 212 222 75 [2.95] [2.56] [2.68] [0.79] [1.77] [0.98] [1.18] [0.18] [1.65] [3.35] [1.81] [0.79] [0.59] [0.18] [0.2] [1.26] [0.12] [0.2] [6.93] [8.35] [8.74] [0.06] [0.14] [0.18] [0.18] [9.92] [9.25] [9.25] [0.31] [0.31] 65 5 5 32 -v + v 5 1 1 3 5 8 4 performance data
model lep150f-24 lep150f-36 lep150f-48 dc output +24v 6.3 ( peak 12 ) a +36v 4.2 ( peak 8 ) a +48v 3.2 ( peak 6 ) a specifications model lep150f-24 lep150f-36 lep150f-48 input voltage[v] ac85 - 264 1 f or dc 120 - 370 current[a] acin 100v 2.0typ ( io=100% ) acin 200v 1.0typ ( io=100% ) frequency[hz] 50/60 ( 47-63 ) or dc efficiency[%] acin 100v 82typ ( io=100% ) 83typ ( io=100% ) 84typ ( io=100% ) acin 200v 85typ ( io=100% ) 86typ ( io=100% ) 87typ ( io=100% ) power factor acin 100v 0.98typ ( io=100% ) acin 200v 0.93typ ( io=100% ) inrush current[a] acin 100v 15typ ( io=100% )( at cold start )( ta=25 c ) acin 200v 30typ ( io=100% )( at cold start )( ta=25 c ) leakage current[ma] 0.75max ( 60hz , according to iec60950 and den-an ) output voltage[v] +24 +36 +48 current[a] * 2 0 - 6.3 ( peak 12 ) 0 - 4.2 ( peak 8 ) 0 - 3.2 ( peak 6 ) wattage[w] 151.2 ( peak 288 ) 151.2 ( peak 288 ) 153.6 ( peak 288 ) line regulation[mv] 48max 48max 48max load regulation[mv] 76max 90max 150max ripple[mvp-p] 0to+45 c * 3 120max 120max 150max -10-0 c * 3 160max 160max 300max ripple noise[mvp-p] 0to+45 c * 3 150max 150max 250max -10-0 c * 3 180max 180max 350max temperature regulation[mv] 0to+45 c 120max 150max 240max -10 to +45 c 145max 180max 300max drift[mv] * 4 48max 48max 48max start-up time[ms] 500max ( acin 100v , io=100% ) hold-up time[ms] 20typ ( acin 100v , io=100% ) output voltage adjustment range[v] 21.4 - 26.4 26.4 - 39.6 39.6 - 52.8 output voltage setting[v] 23.0 - 25.0 35.0 - 37.0 46.0 - 50.0 protection circuit and others overcurrent protection works over 101% of peak current and recovers automatically overvoltage protection works at 115 - 140% of rating remote on/off option ( refer to instruction manual ) isolation input-output - rc * 5 ac3 , 000v 1minute , cutoff current = 10ma , dc500v 50m w min ( at room temperature ) input-fg ac2 , 000v 1minute , cutoff current = 10ma , dc500v 50m w min ( at room temperature ) output - rc-fg * 5 ac500v 1minute , cutoff current = 100ma , dc500v 50m w min ( at room temperature ) output-rc * 5 ac100v 1minute , cutoff current = 100ma , dc100v 10m w min ( at room temperature ) environment operating temp. , humid.and altitude -10 to +70 c , 20 - 90%rh ( non condensing )( refer to derating curve ), 3 , 000m ( 10 , 000feet ) max storage temp. , humid.and altitude -20 to +75 c , 20 - 90%rh ( non condensing ), 9 , 000m ( 30 , 000feet ) max vibration 10 - 55hz , 19.6m/s 2 ( 2g ), 3minutes period , 60minutes each along x , y and z axis impact 196.1m/s 2 ( 20g ), 11ms , once each x , y and z axis safety and noise regulations agency approvals ul60950-1 , c-ul ( csa60950-1 ), en60950-1 , en60065 , en50178 complies with den-an and iec60950-1 ( at only ac input ) conducted noise complies with fcc-b , cispr22-b , en55022-b , vcci-b harmonic attenuator complies with iec61000-3-2 others case size/weight 85 x 40 x 222mm [3.35 x 1.57 x 8.74 inches] ( w x h x d ) /490g max ( without chassis and cover ) cooling method convection * 7 * 1 specification is changed at option, refer to instruction manual 6. * 2 peak loading for 10sec. and duty 35% max, refer to instruction manual 5. in detail. * 3 this is the value that measured on measuring board with capacitor of 22 m f within 150mm from output terminal.measured by 20mhz oscilloscope or ripple-noise meter (equivalent to keisoku-giken: rm101). * 4 drift is the change in dc output for an eight hour period after a half-hour warm-up at 25 c , with the input voltage held constant at the rated input/output. * 5 applicable when remote control (optional) is added. * 6 please contact us about safety approvals for the model with option. * 7 please contact us about class c. * parallel operation with other model is not possible. * derating is required when operated with chassis and cover. * a sound may occur from power supply at peak loading. lep150f ac-dc power supplies open frame/ enclosed type lep 150 f -24 - o ordering information 1 series name 2 output wattage 3 universal input 4 output voltage 5 optional * 1 * 6 g :low leakage current r :with remote on/off s :with chassis sn:with chassis & cover t :vertical terminal block u :operating stop voltage is set at a lower value z :with zt r 12345 lep lep-4 recommended emi/emc filter nac-06-472 high voltage pulse noise type : nap series low leakage current type : nam series * the emi/emc filter is recommended * to connect with several devices.
? input harmonic current ( lep150f-24 ) ? efficiency ( lep150f-24 ) ? input harmonic current ( lep150f-24 ) ? rise time & fall time ( lep150f-24 ) dc output ac input io=100% 20ms/div 100ms/div acin 100v 100 60 140 180 220 260 300 100% 50% load factor load factor efficiency input voltage v 010203040 0.01 0.001 0.1 1 10 load factor input voltage ac harmonic current standard class a (at odd number) 100% 100v harmonic order harmonic current a 010203040 0.01 0.001 0.1 1 10 load factor input voltage ac harmonic current standard class a (at odd number) 100% 230v harmonic order harmonic current a 88 82 80 78 86 84 76 lep lep-5 lep150f external view i / o connector mating connector terminal (mfr: j.s.t.) cn1 cn2 cn3 cn4 b3p5-vh b8p-vh b2b-xh-a b3b-xh-a vhr-5n vhr-8n xhp-2 xhp-3 chain : svh-21t-p1.1 loose: bvh-21t-p1.1 chain : svh-21t-p1.1 loose: bvh-21t-p1.1 chain : sxh-001t-p0.6 loose: bxh-001t-p0.6 chain : sxh-001t-p0.6 loose: bxh-001t-p0.6 ? keep drawing current per pin below 5a(7a at peak load)for cn2 ? weight: 490g max ? tolerance: t 1 [ t 0.04] ? dimensions in mm, [ ]=inches ? pcb material : cem3 ? chassis and cover is optional. ? mounting torque: 1.5n m(16kgf cm)max pin connection pin no. 1 2 3 4 5 input ac(l) ac(n) fg cn1 (option) pin no. remote on/off cn3 rc( + ) rc( - ) 1 2 (option) pin no. -z cn4 + com - 1 2 3 (without chassis and cover) (option) (option) 235 + - 0.5 35 30 20 + + - 0.5 55 - 0.5 cn1 2- o 4.5 235 + - 0.5 o 4.5 2-m4 mounting hole mounting hole 4- m4 name plate voltage adjust 5 mounting hole 4- o 3.5 105 [4.13] [0.2] [8.35] [0.14] [0.18] [0.18] [9.92] [9.25] [0.31] [9.25] [0.31] [8.46] [8.74] + - 0.5 212 222 + - 0.5 + - 0.5 pcb t=1.6 (lead) 3 max rc( - ) rc( + ) + com - cn4 cn3 connector for remote on/off (option) connector for -z (option) pin no. output cn2 1 , , 23 , 4 , 67 , 8 5 , - v + v [0.06] mounting hole o 3.5 - 4.0 [0.14 - 0.16] cn4 4.5 8 95 cn2 4.5 cn4 cn3 15 51 25 8 252 cn3 (68) (215) 5 75 85 [3.35] 37 47 -v + v input(l) input(n) fg [2.95] [2.68] [2.16] [0.79] [1.18] [1.38] [0.18] [0.18] [0.59] [0.98] [2.01] [1.85] [3.74] [0.2] [1.46] [0.12] 5 cn1 1 5 1 cn2 8 4 c119 3 performance data
model lep240f-24 lep240f-36 lep240f-48 dc output +24v 10 ( peak 20 ) a +36v 6.7 ( peak 13.4 ) a +48v 5 ( peak 10 ) a specifications model lep240f-24 lep240f-36 lep240f-48 input voltage[v] ac85 - 264 1 f or dc 120 - 370 current[a] acin 100v 3.3typ ( io=100% ) acin 200v 1.7typ ( io=100% ) frequency[hz] 50/60 ( 47-63 ) or dc efficiency[%] acin 100v 83typ ( io=100% ) 84typ ( io=100% ) 84typ ( io=100% ) acin 200v 86typ ( io=100% ) 87typ ( io=100% ) 87typ ( io=100% ) power factor acin 100v 0.98typ ( io=100% ) acin 200v 0.93typ ( io=100% ) inrush current[a] acin 100v 15typ ( io=100% )( more than 3sec.to re-start ) acin 200v 30typ ( io=100% )( more than 3sec.to re-start ) leakage current[ma] 0.75max ( 60hz , according to iec60950 and den-an ) output voltage[v] +24 +36 +48 current[a] * 2 0-10 ( peak 20 ) 0 - 6.7 ( peak 13.4 ) 0-5 ( peak 10 ) wattage[w] 240.0 ( peak 480 ) 241.2 ( peak 482.4 ) 240.0 ( peak 480 ) line regulation[mv] 48max 48max 48max load regulation[mv] 76max 90max 150max ripple[mvp-p] 0to+40 c * 3 120max 120max 150max -10-0 c * 3 160max 160max 300max ripple noise[mvp-p] 0to+40 c * 3 150max 150max 250max -10-0 c * 3 180max 180max 350max temperature regulation[mv] 0to+40 c 120max 150max 240max -10 to +40 c 145max 180max 300max drift[mv] * 4 48max 48max 48max start-up time[ms] 500max ( acin 100v , io=100% ) hold-up time[ms] 20typ ( acin 100v , io=100% ) output voltage adjustment range[v] 21.4 - 26.4 26.4 - 39.6 39.6 - 52.8 output voltage setting[v] 23.0 - 25.0 35.0 - 37.0 46.0 - 50.0 protection circuit and others overcurrent protection works over 101% of peak current and recovers automatically overvoltage protection works at 115 - 140% of rating remote on/off option ( refer to instruction manual ) isolation input-output - rc * 5 ac3 , 000v 1minute , cutoff current = 10ma , dc500v 50m w min ( at room temperature ) input-fg ac2 , 000v 1minute , cutoff current = 10ma , dc500v 50m w min ( at room temperature ) output - rc-fg * 5 ac500v 1minute , cutoff current = 100ma , dc500v 50m w min ( at room temperature ) output-rc * 5 ac100v 1minute , cutoff current = 100ma , dc100v 10m w min ( at room temperature ) environment operating temp. , humid.and altitude -10 to +70 c , 20 - 90%rh ( non condensing )( refer to derating curve ), 3 , 000m ( 10 , 000feet ) max storage temp. , humid.and altitude -20 to +75 c , 20 - 90%rh ( non condensing ), 9 , 000m ( 30 , 000feet ) max vibration 10 - 55hz , 19.6m/s 2 ( 2g ), 3minutes period , 60minutes each along x , y and z axis impact 196.1m/s 2 ( 20g ), 11ms , once each x , y and z axis safety and noise regulations agency approvals ul60950-1 , c-ul ( csa60950-1 ), en60950-1 , en60065 , en50178 complies with den-an and iec60950-1 ( at only ac input ) conducted noise complies with fcc-b , cispr22-b , en55022-b , vcci-b harmonic attenuator complies with iec61000-3-2 others case size/weight 95 x 45 x 222mm [3.74 x 1.77 x 8.74 inches] ( w x h x d ) /690g max ( without chassis and cover ) cooling method convection * 7 * 1 specification is changed at option, refer to instruction manual 6. * 2 peak loading for 10sec. and duty 35% max, refer to instruction manual 5. in detail. * 3 this is the value that measured on measuring board with capacitor of 22 m f within 150mm from output terminal.measured by 20mhz oscilloscope or ripple-noise meter (equivalent to keisoku-giken: rm101). * 4 drift is the change in dc output for an eight hour period after a half-hour warm-up at 25 c , with the input voltage held constant at the rated input/output. * 5 applicable when remote control (optional) is added. * 6 please contact us about safety approvals for the model with option. * 7 please contact us about class c. * parallel operation with other model is not possible. * derating is required when operated with chassis and cover. * a sound may occur from power supply at peak loading. lep240f ac-dc power supplies open frame/ enclosed type lep 240 f -24 - o ordering information 1 series name 2 output wattage 3 universal input 4 output voltage 5 optional * 1 * 6 g :low leakage current r :with remote on/off s :with chassis sn:with chassis & cover t :vertical terminal block u :operating stop voltage is set at a lower value z :with zt r 12345 lep lep-6 recommended emi/emc filter nac-06-472 high voltage pulse noise type : nap series low leakage current type : nam series * the emi/emc filter is recommended * to connect with several devices.
? input harmonic current ( lep240f-24 ) ? efficiency ( lep240f-24 ) ? input harmonic current ( lep240f-24 ) ? rise time & fall time ( lep240f-24 ) dc output ac input io=100% 20ms/div 100ms/div acin 100v 80 82 84 86 88 78 110 160 210 260 60 310 100% 50% load factor load factor efficiency input voltage v 010203040 0.01 0.001 0.1 1 10 load factor input voltage ac harmonic current standard class a (at odd number) 100% 100v harmonic order harmonic current a 010203040 0.01 0.001 0.1 1 10 load factor input voltage ac harmonic current standard class a (at odd number) 100% 230v harmonic order harmonic current a lep lep-7 lep240f external view i / o connector mating connector terminal (mfr: j.s.t.) cn1 cn2 cn3 cn4 b3p5-vh b8p-vh b2b-xh-a b3b-xh-a vhr-5n vhr-8n xhp-2 xhp-3 chain : svh-21t-p1.1 loose: bvh-21t-p1.1 chain : svh-21t-p1.1 loose: bvh-21t-p1.1 chain : sxh-001t-p0.6 loose: bxh-001t-p0.6 chain : sxh-001t-p0.6 loose: bxh-001t-p0.6 ? keep drawing current per pin below 5a(7a at peak load)for cn2 ? weight: 690g max ? tolerance: t 1 [ t 0.04] ? dimensions in mm, [ ]=inches ? pcb material : cem3 ? chassis and cover is optional. ? mounting torque: 1.5n m(16kgf cm)max pin connection pin no. 1 2 3 4 5 input ac(l) ac(n) fg cn1 (option) pin no. remote on/off cn3 rc( + ) rc( - ) rc( - ) rc( + ) 1 2 (option) pin no. -z cn4 + com - + com - 1 2 3 (without chassis and cover) (option) (option) cn4 cn3 mounting hole 4- o 3.5 name plate connector for remote on/off (option) 512 [4.88] [8.35] [8.74] [8.39] [0.14] [0.2] 4 + - 0.5 222 212 + - 0.5 pcb t=1.6 5 95 [3.74] [3.35] [2.6] [0.2] 85 + - 0.5 45 + - 0.5 65 + - 0.5 (lead) 3 max connector for -z (option) 2- o 4.5 o 4.5 2-m4 mounting hole mounting hole 4-m4 235 + - 0.5 235 + - 0.5 252 pin no. output cn2 1 , , 23 , 4 , 67 , 8 5 , - v + v voltage adjust [0.06] [1.65] [0.12] mounting hole o 3.5 - 4.0 [0.14 - 0.16] [0.18] [9.25] [9.25] [9.92] [0.31] [0.31] [0.18] [2.56] [0.91] [1.3] [1.77] [0.18] [0.18] [2.05] [4.25] [0.59] [1.18] [2.28] (66) cn4 4.5 52 8 cn2 33 23 4.5 cn4 cn3 15 30 58 8 cn3 (213) 42 108 cn1 input(l) input(n) fg -v + v 3 c119 cn2 5 1 5 1 8 4 cn1 performance data
|
